• Upgraded Direct Replacement for Motorcraft FL-820S oil filter.
  So any application that uses a Motorcraft FL-820S oil filter can benefit
  from using this upgraded oil filter.
• Synthetic-Polymer/Cellulose-Fiber blend media
• Heavy-gauge base and canister for higher burst strength and impulse fatigue resistance
• High-quality silicone anti-drain back valve
• Non-stick sealing gasket for ease of installation and removal
• Long life with standard and synthetic motor oils
• Up to 50% more filtering capacity than standard filters
• Improved filtering efficiency
• This technology is only available through Ford Racing Performance Parts
• Click Here for a Complete Vehicle Application Fitment List

• Hand Poured Urethane Body Won't crack, shrink, or curl like rubber or Plastisol
• Airaid's exclusive unique dry filtration technology enables the filter to filtrate far superior to the average cotton filter
• The last air filter you will need to buy! Dry filter technology is easily cleaned with common household detergents and water.
• 6.76 Rear Wheel HP increase as measured on Airaid's in-ground chassis dyno.
• Proudly Made in the USA with a "No-Hassle" Warranty.

• Fits 2005-2014 Mustangs Ford Performance Hood Lift Kit w/ Laser Engraved Ford Performance Logo.
• 90 LBS Rating
• Designed for all OEM base, Mustang GT, GT500, GT350, and many aftermarket hoods
• These hood lifts utilize two gas struts that lift and hold the hood without the need for a prop-rod.
• Made from lightweight steel and aluminum, they feature a durable black power coated finish to give your engine bay a much cleaner appearance.
• Includes the necessary mounting brackets
• No Drilling Required. The stamped steel brackets included in this kit are designed to bolt into the existing mounting holes in the hood so there is no drilling required for installation
• If your aftermarket hood is lighter than the factory hood, use caution when opening the hood due to the power of the strut.

• Fits 4-valve 5.4L engines
• Production steel primary and secondary timing chain tensioners
• Includes PN F6AZ-6L266-DA and F6AZ-6L266-CA (1 of each PN)
2 kits required per engine

Why these pulleys are better

• Each pulley consists of precision machined grooves to ensure proper fitment with the belt. Inferior designed grooves will rip belts apart. The pulley to belt contact area is a critical design element and the pulley design is the result of many revisions to virtually eliminate slippage.
• To eliminate the issue of the pulley slipping on the supercharger shaft, these pulleys are honed bore, round & straight within .0002.
• Proper Lead-in is designed into each pulley to ensure that the it goes on straight.
• Made In the USA

• Fits 5.4L DOHC engines
• Original equipment on 2007-2011 Mustang SVT and 2008 Mustang FR500CJ race car
• Improved sealing for high cylinder pressure applications
• Kit includes multi-layer steel head gaskets and high-strength torque to yield head bolts

• Upgraded Direct Replacement for Motorcraft FL-820S oil filter.
  So any application that uses a Motorcraft FL-820S oil filter can benefit
  from using this upgraded oil filter.
• Synthetic-Polymer/Cellulose-Fiber blend media
• Heavy-gauge base and canister for higher burst strength and impulse fatigue resistance
• High-quality silicone anti-drain back valve
• Non-stick sealing gasket for ease of installation and removal
• Long life with standard and synthetic motor oils
• Up to 50% more filtering capacity than standard filters
• Improved filtering efficiency
• This technology is only available through Ford Racing Performance Parts
• Click Here for a Complete Vehicle Application Fitment List

• Fits 2007-2014 Mustang Shelby GT500
• New stock replacement 60mm throttle body

• Components are CNC machined out of high quality aluminum.
• High quality Type III hard coat anodized finish.
• True double-bearing setup can withstand anything you throw at it!
• Will work with ALL available superchargers, including the Kenne Bell!
• Designed to work with most common supercharger pulleys.
• Simple installation without modification!

• Unique lash adjusters fit Ford GT and Mustang GT500 5.4L/5.8L DOHC cylinder heads  
• Includes 16 intake and 16 exhaust lash adjusters  

• New factory replacement damper from the 2008-2012 Shelby GT500 5.4L 4V engine
• 10 lbs lighter than the 2007 factory Shelby GT500 Crankshaft Damper
• Must be installed on the 2007 Shelby GT500 Mustang when using the M-6066-SGT on 2007 Shelby GT500 to qualify for warranty.
• Highly recommended for any 2007 Shelby GT500 when upgrading the supercharger.

• Original equipment on Ford GT 5.4L engine
• Fits 4.6L and 5.4L 4V DOHC SVT engines
• 4 grams lighter, stiffer, and better engagement on lash adjuster over 4.6L DOHC rocker arms

• Fits 4.6L/5.4L/Coyote 5.0L
• 4.4:1 Gear Reduction
• 200 ft-lb rating
• Small diameter mini-starter great for additional header and oil pan clearance
• No heat soak problems
• Weighs 8.5 lbs.  The lightest 200 ft-lb starter available.
• Machined Billet Aluminum Adapter Block
• Every starter is individually tested and dyno results sheet is included in the box
• Starter bolts are not included.  Starter bolts can be sourced from your local Ford Dealer.
• Brand New.  Not rebuilt or re-manufactured.
• No core charge
• Made In USA

• Fits 2007-2012 Shelby GT500 5.4L engines
• One engine set of (8) OEM Ford Motorcraft stock replacement coils

• Fits: 2005-2014 Mustang GT  and 2007-2014 Mustang Shelby GT500
• Original equipment cooling fan on 2013-2014 Mustang Shelby GT500
• Added cooling capacity for performance applications

• 80 lbs/hr, single hole, high-impedance fuel injector with USCAR electrical connector.
• Latest technology injector design for optimum performance.
• Original Equipment on the winning Cobra Jet race cars
• Check your current injectors or harness to determine the correct style connector. If it is not the right connector we have a really nice adapter kit to convert the connector of this injector (USCAR) to a Jetronic/Minitimer style connector.
• Need help determining which injector you require for your application? Refer to EFI Tech Tips
• If these injectors are a different size (lbs/hr. flow rate) than the ones currently installed on your vehicle, then you will need recalibrate either your Mass Air Flow sensor or PCM tune for proper performance.