• Upgraded Direct Replacement for Motorcraft FL-820S oil filter.
  So any application that uses a Motorcraft FL-820S oil filter can benefit
  from using this upgraded oil filter.
• Synthetic-Polymer/Cellulose-Fiber blend media
• Heavy-gauge base and canister for higher burst strength and impulse fatigue resistance
• High-quality silicone anti-drain back valve
• Non-stick sealing gasket for ease of installation and removal
• Long life with standard and synthetic motor oils
• Up to 50% more filtering capacity than standard filters
• Improved filtering efficiency
• This technology is only available through Ford Racing Performance Parts
• Click Here for a Complete Vehicle Application Fitment List

• Fits 2005-2010 4.6L 3-valve engine
  
• Kit includes two (2) bolts
  
• Torque to yield design
  
• Torque Information:
  • Stage 1: Tighten to 40 Nm (30 lb-ft).
  • Stage 2: Tighten an additional 90 degrees.
    

• Fits 3-Valve 4.6L modular engine with standard 90.2mm bore and 3-valve head


• Kit includes multi-layer steel head gaskets and high-strength torque-to-yield head bolts

• Fits 2005-2014 Mustangs Ford Performance Hood Lift Kit w/ Laser Engraved Ford Performance Logo.
• 90 LBS Rating
• Designed for all OEM base, Mustang GT, GT500, GT350, and many aftermarket hoods
• These hood lifts utilize two gas struts that lift and hold the hood without the need for a prop-rod.
• Made from lightweight steel and aluminum, they feature a durable black power coated finish to give your engine bay a much cleaner appearance.
• Includes the necessary mounting brackets
• No Drilling Required. The stamped steel brackets included in this kit are designed to bolt into the existing mounting holes in the hood so there is no drilling required for installation
• If your aftermarket hood is lighter than the factory hood, use caution when opening the hood due to the power of the strut.

• For use in engines with higher than stock cylinder combustion pressures
• One heat range colder than the stock Mustang GT plug
• Two heat ranges colder than the stock 5.4L truck 3-valve engine
• Sold in engine sets of 8
• Fits 2008 and newer 3V heads requiring the 12mm thread
  Note: Engines with late style 12MM spark plugs can be identified by coil engineering number 8L3E
  Engines with early style 16mm "High Thread" design spark plugs can be identified by coil engineering number 3L3E part number

• Upgraded Direct Replacement for Motorcraft FL-820S oil filter.
  So any application that uses a Motorcraft FL-820S oil filter can benefit
  from using this upgraded oil filter.
• Synthetic-Polymer/Cellulose-Fiber blend media
• Heavy-gauge base and canister for higher burst strength and impulse fatigue resistance
• High-quality silicone anti-drain back valve
• Non-stick sealing gasket for ease of installation and removal
• Long life with standard and synthetic motor oils
• Up to 50% more filtering capacity than standard filters
• Improved filtering efficiency
• This technology is only available through Ford Racing Performance Parts
• Click Here for a Complete Vehicle Application Fitment List

• 24 lbs/hr, 6-hole, high-impedance fuel injector with USCAR electrical connector.
• Latest technology injector design for optimum performance.
• Check your current injectors or harness to determine the correct style connector. If it is not the right connector we have a really nice adapter kit to convert the connector of this injector (USCAR) to a Jetronic/Minitimer style connector.
• Need help determining which injector you require for your application? Refer to EFI Tech Tips
• If these injectors are a different size (lbs/hr. flow rate) than the ones currently installed on your vehicle, then you will need recalibrate either your Mass Air Flow sensor or PCM tune for proper performance.

Designed to install the M-6010-BOSS50 block in a 2005-2010 Mustang

• Aluminum engine mounting brackets
• Adapter plates
• Hardware

• Fits 4.6L/5.4L/Coyote 5.0L
• 4.4:1 Gear Reduction
• 200 ft-lb rating
• Small diameter mini-starter great for additional header and oil pan clearance
• No heat soak problems
• Weighs 8.5 lbs.  The lightest 200 ft-lb starter available.
• Machined Billet Aluminum Adapter Block
• Every starter is individually tested and dyno results sheet is included in the box
• Starter bolts are not included.  Starter bolts can be sourced from your local Ford Dealer.
• Brand New.  Not rebuilt or re-manufactured.
• No core charge
• Made In USA

• Fits: 2005-2014 Mustang GT  and 2007-2014 Mustang Shelby GT500
• Original equipment cooling fan on 2013-2014 Mustang Shelby GT500
• Added cooling capacity for performance applications

• 47 lbs/hr, 6-hole, high-impedance fuel injector with USCAR electrical connector
• This is a medium length injector designed to lower the fuel rail for increased clearance under the manifold or air inlet tract
• Original Equipment on 2007-2012 Shelby GT500
• Check your current injectors or harness to determine the correct style connector. If it is not the right connector we have a really nice adapter kit to convert the connector of this injector (USCAR) to a Jetronic/Minitimer style connector.
• Need help determining which injector you require for your application? Refer to EFI Tech Tips
• 47 lbs/hr Fuel Injector Calibration Sheet
• If these injectors are a different size (lbs/hr. flow rate) than the ones currently installed on your vehicle, then you will need recalibrate either your Mass Air Flow sensor or PCM tune for proper performance.

• Fits 4.6L 3V cylinder heads
• Original production part as used on 2005-10 Mustang GT
• Sold in engine sets (24 rocker arms and 24 lash adjusters)

• 47 lbs/hr, 6-hole, high-impedance fuel injector with USCAR electrical connector.
• Latest technology injector design for optimum performance.
  
• Check your current injectors or harness to determine the correct style connector.  If it is not the right connector we have a really nice adapter kit to convert the connector of this injector (USCAR) to a Jetronic/Minitimer style connector.
  
• Need help determining which injector you require for your application? Refer to EFI Tech Tips
• If these injectors are a different size (lbs/hr. flow rate) than the ones currently installed on your vehicle, then you will need recalibrate either your Mass Air Flow sensor or PCM tune for proper performance.

• Fits 2005-2010 3-valve 4.6L and 5.4L engines
• Powdercoated blue finish
• Laser Etched Ford Racing Logo
• Includes cam cover gasket

• Fits 2005-2010 3-valve 4.6L and 5.4L engines
• Powdercoated black finish
• Laser Etched Ford Racing Logo
• Includes cam cover gasket

• 80 lbs/hr, single hole, high-impedance fuel injector with USCAR electrical connector.
• Latest technology injector design for optimum performance.
• Original Equipment on the winning Cobra Jet race cars
• Check your current injectors or harness to determine the correct style connector. If it is not the right connector we have a really nice adapter kit to convert the connector of this injector (USCAR) to a Jetronic/Minitimer style connector.
• Need help determining which injector you require for your application? Refer to EFI Tech Tips
• If these injectors are a different size (lbs/hr. flow rate) than the ones currently installed on your vehicle, then you will need recalibrate either your Mass Air Flow sensor or PCM tune for proper performance.